|
#281
|
|||
|
|||
Would you say it's better than the bmax 4 in every way?
Curious to see how it'll go on low traction dirt |
#282
|
||||
|
||||
Quote:
If so I can then use pills from the rear side in the front to change those settings right? Just want to make sure I use the correct starting point!
__________________
Dave "Amish FJ" Gibson RB Products ~ Yokomo Nuclear RC ~ Xpert ~ Hacker |
#283
|
||||
|
||||
I went with the front alu hanger arrow pointing upwards
and with the rear hanger H1-3 dot up(everything with a dot = 3degree of toe), which gives me 3toe 1squat. You should use 0H2 dot up for 2squat then. That is according http://site.petitrc.com/setup/yokomo..._ToeAntiSquat/ Quote:
__________________
==> check out our youtube channel http://www.youtube.com/rcstefracing ==> FB https://www.facebook.com/RCstefracing/ |
#284
|
|||
|
|||
Diffs!
Did anybody else have stiff and notchy diffs when first building? I built mine last week and put in 5,000wt in and they have more resistance, and are "grainy", than my BMax with 10,000. I haven't run yet, hopefully they loosen up.
|
#285
|
||||
|
||||
Quote:
I've seen a gear diff build on youtube that used lapping paste in the gear diff, then using a drill to turn the diff outdrive to do the process, but this seems a bit extreme to me. Just run it.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#286
|
||||
|
||||
Quote:
__________________
Dave "Amish FJ" Gibson RB Products ~ Yokomo Nuclear RC ~ Xpert ~ Hacker |
#287
|
||||
|
||||
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#288
|
||||
|
||||
__________________
Numquam cedunt victores, numquam ignavi vincunt. |
#289
|
||||
|
||||
Quote:
The YZ2 comes with a spacer under the FR and RR hangers. You can chose the run it with or without the spacers. Use it under both hangers and it changes the roll-center a little. Dont recommend to use it under the FR only, as it will change anti-squat
__________________
Schumacher KC - Tekno EB48.3
|
#290
|
||||
|
||||
I had exactly this, did what was suggested above and its a lot better now, but I did notice this during the build as well.
|
#291
|
|||
|
|||
Now that the kit has been out for a few weeks, are there any absolute hop-ups that are needed (such as the Aluminum narrow pulley & belt set) for increased performance on high bite surfaces?
A lot of people over on RCtech are saying there isn't much needed for increased performance - other than the consumables like tyres, oils, springs pistons etc. |
#292
|
||||
|
||||
Most have had one meeting on the car if lucky...
I'd still say buy a kit and run it. Nothing wrong with it out the box. My only feeling is that the servo mounts are rubbish in the kit, and the alloy one is best, however it will still function fine with the kit plastic ones. Roll bars are needed, but they are included with a Yokomo Europe (not CML) sourced kit, other wise an extra. I'd be looking to do rear hangers for adjustment, then steering crank parts, servo mount, upper front ball stud mounts, then maybe belt pulleys. I've all the options on mins at this time, except the YZ4 hangers. I've used YZ2 ones for now, as they are in my box anyway.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#293
|
||||
|
||||
YZ4 suspension hangers
Quick question guys, when ordering the alloy rear suspension hangers for the YZ4, do they come with the plastic insets or do you need to order the suspension mount bush/ bumper kit too?
Cheers guys. 👍🏻 |
#294
|
|||
|
|||
You'll need the additional parts.
|
#295
|
||||
|
||||
Couple of body options if your running indoor. Both fit really well and only require minimal mods to clear pulleys, i wouldnt run them outdoor due to exposure, but its an option if your not a fan of the Lifeboat kit shell.
lee
__________________
INSERT COIN
|
#296
|
|||
|
|||
Quote:
Z4-300RRS Z4-300RFS
__________________
www.facebook.com/racewayone RACEWAYONE :: LMR :: MIBOSPORT :: RC CONCEPT :: SMD Trader Feedback: http://oople.com/forums/showthread.php?t=81070 |
#297
|
|||
|
|||
I haven't seen any input on those spacers as yet, but I guess I'll want them before long. However, I don't know what to think of the pricing of these sets. We are talking of close to 30 euros for some bits of stamped metal (both sets). So far, at least Yokomo's non-machined parts used to be available at decent prices. What's going on? I am really happy with both my YZ cars, but the price of these thingies has put a dent into Yokomo's reputation for me, and I've been a fanboy since the early 90s... IMHO these thingies should be included in the kit or at least come with the aluminium hangers. Ridiculous...
|
#298
|
|||
|
|||
Quote:
I thought that the width of them would be off? Unless it's for another car? |
#299
|
||||
|
||||
Both AE fitting, chassis width and profile is spot on!
Lee
__________________
INSERT COIN
|
#300
|
|||
|
|||
Quote:
__________________
www.facebook.com/racewayone RACEWAYONE :: LMR :: MIBOSPORT :: RC CONCEPT :: SMD Trader Feedback: http://oople.com/forums/showthread.php?t=81070 |
|
|