|
||
|
 |
|
||||||||||||||||||
|
#1
24-02-2009
|
||||
|
||||
Cat SX wing holder
Any suggestions how to replace original? I managed to break both rubber o-rings in 4 practice runs in Vienna. Or do you have any trick to make them more durable?
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。| | Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts | 
|
|
#2
24-02-2009
|
|||
|
|||
|
I use Kyosho ZX5 wing holders, they fits well. And is hard to broke.. Have running the same Kyosho car in three seasons with the same wing holders..
__________________
Ulrich Rasmussen Denmark Danish 4WD champion 1989, 1997, 2003, 2004, 2005, 2006 and 2007. www.racegallery.dk
|
|
#3
24-02-2009
|
||||
|
||||
|
Losi wing mounts?
__________________
|
|
#4
24-02-2009
|
||||
|
||||
|
tamiya 501x wing mounts are a good fit i believe
__________________
Custom MG-Racing Associated DMS
|
|
#5
24-02-2009
|
||||
|
||||
|
Been running the same 4 o-rings for about 7 or 8 meetings now!!! Did you have any big crashes? They shouldnt break within that amount of time!!Someone told me you can use cable ties to secure your wing if you use them just like you would with the O-rings. Or try and find some thicker O-rings.
Ben
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models
|
|
#6
25-02-2009
|
||||
|
||||
|
Quote:
Quote:
No they weren't big, just ordinary roll on leaving corner tabletop 
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。| | Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts |
|
|
#7
25-02-2009
|
|||
|
|||
|
tamiya 501x mounts are a straight swap
|
|
#8
25-02-2009
|
||||
|
||||
|
Chamfer the edge of the top button. Originally this holder was designed for only one O-ring.Two rings just need to have a little more room and the sharp edge of the button just cuts it.
Cruise
__________________
Team CS-Electronic Team Schumacher
|
|
#10
25-02-2009
|
|||
|
|||
|
Quote:
__________________
 ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
|
#11
26-02-2009
|
||||
|
||||
|
Quote:
Here is an example: 
__________________
http://www.mid44.com/
|
|
#12
11-03-2009
|
||||
|
||||
|
Any one know the part number for the tamiya wing mounts???
|
|
#13
12-03-2009
|
||||
|
||||
|
Quote:
 
__________________
http://www.mid44.com/
|
|
#14
12-03-2009
|
||||
|
||||
|
nice one...thanks!!
|
|
#15
12-03-2009
|
||||
|
||||
|
Sorry,but do you know where I can get these parts??
|
|
#17
12-03-2009
|
|||
|
|||
|
Kyosho ZX5 wing mounts
Kyosho ZX5 wing mounts is similar, maybe a little lower wing position than Tamiyas.
I think Kyoshos is easier to find in shops. And fit direct on shock tower.
__________________
Ulrich Rasmussen Denmark Danish 4WD champion 1989, 1997, 2003, 2004, 2005, 2006 and 2007. www.racegallery.dk
|
|
#18
12-03-2009
|
||||
|
||||
|
That's great....thanks!!
|
|
#19
12-03-2009
|
||||
|
||||
|
is it this-Kyosho Front Bumper/Wing Stay - Lazer ZX-5
|
|
#20
12-03-2009
|
|||
|
|||
|
Yes.. correct.. I like the kyosho more than tamiya, because Kyoshos have clips/washer than Tamiya with screw/small washer. So you have to find some small body clips to.
Quote:
__________________
Ulrich Rasmussen Denmark Danish 4WD champion 1989, 1997, 2003, 2004, 2005, 2006 and 2007. www.racegallery.dk
|
 |
|
|
Schumacher
Linear Mode
