Go Back   oOple.com Forums > Car Talk > Schumacher

Reply
 
Thread Tools Display Modes
  #1  
Old 09-09-2009
Brooks's Avatar
Brooks Brooks is offline
Member
 
Join Date: Jun 2009
Location: England
Posts: 297
Default Schumacher Cat Sx Spur Gear meshing problems

Hi people

Have been having probs tyring to mesh the standard spur with a 22 pinion.

At one point i think its meshed, then you turn the spur again and the pinion is either too tight on the spur or so loose that the motor with shread the Spur as its too far away.

It doesnt look like the spurs are total round
I replaced one with another and it was the same

Has anybody had these problems

Cheers
Chris B
Reply With Quote
  #2  
Old 09-09-2009
jim76 jim76 is offline
*SuPeRsTaR mEmBeR*
 
Join Date: May 2006
Location: ruislip
Posts: 2,890
Default

check your motor is in the motor mount squarely.
__________________
4wd - X4TE
2wd - X2C (Mad Rat passed down to son!)

Ansmann Racing UK


RIP - MicroTech Racing

Trader Feedback
Reply With Quote
  #3  
Old 09-09-2009
lochness42's Avatar
lochness42 lochness42 is offline
Mad Member
 
Join Date: Apr 2008
Location: Battersea, London, UK
Posts: 1,269
Send a message via ICQ to lochness42 Send a message via MSN to lochness42 Send a message via Skype™ to lochness42
Default

Also check your front motor plate - one of my runs was ruined by loose motor plate resulting in stripped spur.
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。|
| Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts |
Reply With Quote
  #4  
Old 09-09-2009
_sleigh_ _sleigh_ is offline
Mad Member
 
Join Date: Jul 2006
Location: In front of my PC
Posts: 1,920
Default

I'd probably start with checking the layshaft isn't bent
Reply With Quote
  #5  
Old 09-09-2009
super__dan's Avatar
super__dan super__dan is offline
#1 ZX5 fan
 
Join Date: Feb 2006
Posts: 3,482
Default

Or that the layshaft bearing hasn't collapsed
__________________


Nortech is ACE!
Reply With Quote
  #6  
Old 09-09-2009
bigred5765's Avatar
bigred5765 bigred5765 is offline
Lion-O - King of the Thundercats
 
Join Date: Mar 2006
Location: chorley
Posts: 8,474
Send a message via MSN to bigred5765 Send a message via Skype™ to bigred5765
Default

check all of the above all good suggestions, but also make sure the spur gear hasn't slightly melted from slipping to much and made the center hole to big?
__________________
Mattys the driver,my names carl
Reply With Quote
  #7  
Old 09-09-2009
jim76 jim76 is offline
*SuPeRsTaR mEmBeR*
 
Join Date: May 2006
Location: ruislip
Posts: 2,890
Default

i was going to suggest that, but then realised he'd already swapped the spur and still had the problem.
Move to B4 spurs if you can, get the layshaft altered.
__________________
4wd - X4TE
2wd - X2C (Mad Rat passed down to son!)

Ansmann Racing UK


RIP - MicroTech Racing

Trader Feedback
Reply With Quote
  #8  
Old 09-09-2009
James's Avatar
James James is offline
RHR RACING
 
Join Date: Jan 2007
Location: Worksop/Blyth Tracks Nottinghamshire
Posts: 2,457
Send a message via MSN to James
Default

Check:

Rear gearbox housings arent tweaked
Layshaft bearings are ok
Layshafts straight
Motor Clamp hasnt twisted motor - or the sticker on the motor hasnt been 'ruffled' when clamped

Bigger spurs seem to mesh better on my car eg 84/23 on a 6.5 is what i ran at RHR national
__________________
~JAMES HELLIWELL~ROBIN HOOD RACEWAY~RHR DIRT~WORKSOP RACEWAY~BIRDS EYE VIEW~
Reply With Quote
  #9  
Old 09-09-2009
Brooks's Avatar
Brooks Brooks is offline
Member
 
Join Date: Jun 2009
Location: England
Posts: 297
Default

thanks alot people

Will check all that tonight and let you know
Reply With Quote
  #10  
Old 09-09-2009
Brooks's Avatar
Brooks Brooks is offline
Member
 
Join Date: Jun 2009
Location: England
Posts: 297
Default

I checked the Layshaft bearings and they were ok and the Layshaft was straight
Motor Clamp hadnt twisted motor and checked the motor bearing and they were fine

Tyred meshing it again and it did seem better but still hard to get it the right meshing all round
Reply With Quote
  #11  
Old 09-09-2009
James's Avatar
James James is offline
RHR RACING
 
Join Date: Jan 2007
Location: Worksop/Blyth Tracks Nottinghamshire
Posts: 2,457
Send a message via MSN to James
Default

Mines a bit like that, its hard to tell if the bearings have gone too, maybe change them as a matter of course next time you do a strip down..
Good luck
__________________
~JAMES HELLIWELL~ROBIN HOOD RACEWAY~RHR DIRT~WORKSOP RACEWAY~BIRDS EYE VIEW~
Reply With Quote
  #12  
Old 15-09-2009
Brooks's Avatar
Brooks Brooks is offline
Member
 
Join Date: Jun 2009
Location: England
Posts: 297
Default

Seems worse now, have taken the layshaft apart again, fitted a brand new one and its even worse

The motor meshing goes from out to in

Help Again People
Reply With Quote
  #13  
Old 15-09-2009
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

daft question, have you tried a different motor to make sure the armature isnt bent ??
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #14  
Old 15-09-2009
jim76 jim76 is offline
*SuPeRsTaR mEmBeR*
 
Join Date: May 2006
Location: ruislip
Posts: 2,890
Default

or rebuild the whole rear end to make sure the gearbox sides haven't been moved in a shunt? You can check them to make sure they aren't buckled slightly also while they are off the car.
__________________
4wd - X4TE
2wd - X2C (Mad Rat passed down to son!)

Ansmann Racing UK


RIP - MicroTech Racing

Trader Feedback
Reply With Quote
  #15  
Old 15-09-2009
Brooks's Avatar
Brooks Brooks is offline
Member
 
Join Date: Jun 2009
Location: England
Posts: 297
Default

Will check that

I did try a different motor and it was the same problem
Reply With Quote
  #16  
Old 15-09-2009
Dazzler's Avatar
Dazzler Dazzler is offline
Senior Member
 
Join Date: Nov 2008
Location: Telford
Posts: 902
Default

Did you say you replaced the layshaft or was it the spur you replaced? I was just wondering if the layshaft had been reduced in diameter to accept the AE spur that some people are fitting. If it has and then you are fitting an original Schumacher spur, it may not be located concentrically. You'll obviously know if the layshaft is standard or not if you have owned the car from new...
Check the location of the spur on the shaft to ensure a good fit, maybe mark the high and low spot then remove the spur and measure from the bore diameter to the spur outer diameter with a vernier calliper (if you have one) at both the high and low spots previously marked up. I can't see a tweek or similar causing what you are describing, only something that rotates and is bent or out of concentricity will cause it.

One things for sure, when you do eventually find out what it is, it'll be obvious i'm sure! Good luck.
Reply With Quote
  #17  
Old 15-09-2009
MALLET's Avatar
MALLET MALLET is offline
Senior Member
 
Join Date: Jan 2008
Location: S in A. Notts
Posts: 608
Default

I'd change your bearings as James has said
__________________
PBMracing

www.ndor.co.uk

My Feedback
Reply With Quote
  #18  
Old 15-09-2009
lochness42's Avatar
lochness42 lochness42 is offline
Mad Member
 
Join Date: Apr 2008
Location: Battersea, London, UK
Posts: 1,269
Send a message via ICQ to lochness42 Send a message via MSN to lochness42 Send a message via Skype™ to lochness42
Default

If you've got someone with Cat somewhere around you should try to swap part after part and find out what is causing problem. That will be cheapest and easiest way.
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。|
| Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts |
Reply With Quote
  #19  
Old 16-09-2009
Mossy Mossy is offline
Senior Member
 
Join Date: Feb 2007
Location: Stoke
Posts: 553
Send a message via MSN to Mossy
Default

If your coming to the F3s ill take a look if your still struggling.

Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC
Reply With Quote
  #20  
Old 16-09-2009
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

if you are suffering from loose/tight mesh, then that is something rotating out of true, so if you had bent housings and what not, it wouldn't do that. I would concentrate on the layshaft and slipper assembly.

Take the slipper off, and rotate the drivetrain, and see if there is any deflection on the layshaft, if there is, either it is a bearings or the shaft. If there is no deflection, assemble the slipper, one part at a time, and see what pulls it out of line. I would also strongly advise on checking to see if the spur gear alone, rotates true.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com