|
#61
|
||||
|
||||
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#62
|
|||
|
|||
Phil, was not aware you had sent the speedo away to them (Tekin), I hope they have sorted it out for you, last I knew you were emailing their tech department for advice.
Must of been somthing wrong with the original for them to have swapped it, assuming it isnt the same one refurbed they have sent you back that is. Let us know if there are any further problems.....
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#63
|
|||
|
|||
I have software version 180 in my RS Pro and am looking to install this into a CAT SX running Lipo and going to a 6.5 SpeedPassion motor. Gearing will be around 23/83 giving a FDR of 9.32. Does anyone have more Hotwire setting suggestions for this sort of setup?
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#64
|
||||
|
||||
9.32 might be a little steep, try it on a 22 initialy.
Timing set to 80 Limiter to 95 TP3 Neutral 10 Thats a good starting point, but if you got Hotwire, let the hotwire update your software!
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#65
|
|||
|
|||
I have seen setup sheets where they are using that gear ratio on a 5.5. I tried a 21 on a 5.5 and it was insane especially when using LiPo so I am currently running an 18 which is much more controlable. I have the Hotwire so I am looking forward to when Tekin release the newer firmware which from what I read will be 183 or maybe 189.
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#66
|
||||
|
||||
The Tekin RS Pro is a gr8 bit of kit.
Ive changed the settings to the highest punch setting and all seems fine and dandy in 4wd buggies. I have had a couple of glitches where the esc needs reprogramming as its for some daft reason its forgotten whats what but the esc works fine. No over heating which is good. Its also a heck of a lot smoother and better to drive than the sensorless esc's (i have two mamba max esc and they are not as good) and the motors seem much more manageable compared to the sensorless. I also found that the Tekin work really well with Corally compared to anything else. No idea why. If your want a speedy reply email Jim at Tekin, he is pretty quick at sending a response relating to anything.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#67
|
||||
|
||||
what is the "punch setting" ?
i am french i run with trf501x, vortex 6.5 and 19/96= 10.3 ratio and i have not a good punch . i have 80% timing , linear trottle profile. with this configuration i have a low punch why? thanks seb |
#68
|
|||
|
|||
You must have software version 189 or higher to have timing boost for spec motors. The team has been testing version 194 which is now available from Randy, rpike@teamtekin.com
Tekin Prez Jim Campbell |
|
|