|
#1
|
||||
|
||||
K2 Ball sockets and ball studs
Can anyone give me a list of the bits needed to replace the K2's original ball sockets and ball studs front and back also for the steering linkage's, I want to use the standard parts as the k2 ones are a bit rubbish.
Or is there any sign of Schumacher replacing them with better materials as I like the idea of the sockets not being able to pop off but it's annoying having to set camber and toe after every race. Thanks.
__________________
|
#2
|
||||
|
||||
If you get the lunsford super duty turnbuckles then this solves the issue, plus it makes the car a lot stronger
__________________
'There are two choices in life-Take it or leave it !' Yokomo - Nemoracing Sb Designs http://www.fairfueluk.com/ |
#3
|
||||
|
||||
Does that mean i can stick with the original sockets and studs ?
__________________
|
#4
|
||||
|
||||
yup
__________________
'There are two choices in life-Take it or leave it !' Yokomo - Nemoracing Sb Designs http://www.fairfueluk.com/ |
#5
|
||||
|
||||
Cool thanks for the advise
__________________
|
#6
|
||||
|
||||
Turnbuckles
Anybody got list or part numbers
|
#7
|
||||
|
||||
If you ring mb models he has supplied my self and some other people with the ones you need.
__________________
'There are two choices in life-Take it or leave it !' Yokomo - Nemoracing Sb Designs http://www.fairfueluk.com/ |
#8
|
|||
|
|||
My self I went to the standard kf2 ball cups and joints, if you want to use the schuamcher parts here are the part numbers :thumbs:
Ballstuds: Long: U4275 x2 Short: U4274 Ultra short:U4273 Ballcups: U4704 Hope this helps
__________________
Current car line up Team Associated B6 - Reedy - Sanwa -Savox Team Associated B64 - Reedy - Sanwa -Savox Sponsors - Team Associated - CML - Pure-RC - RudeBits - Puppy Paint |
#9
|
||||
|
||||
I rang mb and They were not too sure as to which Lunsford ones to use as the people who ordered them specifically asked for the correct equivalent.
I think what I need is: 4x 52mm 2x 45mm 1x 35mm I think they are a 3.5mm thread which is the super duty range and they don't do 35mm and 45mm in that type, only in the punisher range they do but they are 3mm thread.
__________________
Last edited by Noob; 29-06-2016 at 09:41 PM. |
#10
|
||||
|
||||
If anyone is interested, here is the part numbers I ordered from DMS:
L11070BC L11064BC L11067BC the sizes might not be perfect but are closest you can get.
__________________
Last edited by Noob; 04-07-2016 at 05:15 PM. |
#11
|
||||
|
||||
That looks right, tight fit but they work!
__________________
'There are two choices in life-Take it or leave it !' Yokomo - Nemoracing Sb Designs http://www.fairfueluk.com/ |
#12
|
|||
|
|||
Are schumacher going to address this design flaw with new parts and replacement parts to people who have bought kits or are the expecting people to buy aftermarket parts to sort out the problem
|
#13
|
||||
|
||||
Quote:
I've only had one go, basically the thread pushed all the way in and gave me some wicked camber, lol But this was my fault as I crashed, really heavy. I've had more issues with piston rods breaking than the new rod ends, but again that's me pushing to hard and crashing. ?
__________________
Schumacher Speed Passion Futaba Support from: My Back Pocket Driver - 'Derek' Feedback Link : http://www.oople.com/forums/showthread.php?t=48311 |
#14
|
||||
|
||||
They get so loose you can turn the turn buckles with your hands.
Lundsford upgrades sorted it out.
__________________
|
#15
|
||||
|
||||
I find a drop of super glue tightens them up quite nicely
|
|
|