|
#61
|
||||
|
||||
Yes, the last email i got from the model shop was the 20th May
__________________
Schumacher Cougar Laydown, CAT 2000, Cougar 2000/95 spec, Cougar 2000 94 spec, Cougar Mk1, Top Cat, Mardave Meteor. |
#62
|
||||
|
||||
I was told last night by Schumacher that it will probably be the tail end of next week.
__________________
I live with fear everyday....sometimes she lets me race!!!! Schumacher F1..The original KF. TLR 5.0 AC .. FORSALE |
#63
|
||||
|
||||
Nice...
|
#64
|
||||
|
||||
Any updates, is this still likely?
|
#65
|
||||
|
||||
Your probably better off calling Schumacher and asking.
__________________
I live with fear everyday....sometimes she lets me race!!!! Schumacher F1..The original KF. TLR 5.0 AC .. FORSALE |
#66
|
||||
|
||||
As of yesterday I was told the new part(s) are with Schumacher. So they need to be checked out. Assuming they pass Q.C then they'll then start packing kits, so fingers crossed the wait is nearly over.
|
#67
|
|||
|
|||
Yep, claws crossed!
|
#68
|
|||
|
|||
The cakes have been served at Schumacher according to their FB page.
|
#69
|
||||
|
||||
If your on the fence, can highly recommend one
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#70
|
|||
|
|||
mb confirmed will be in shop tomorrow
__________________
STARTED IN FEBRUARY 2018 LEARN'T WITH A DEX210, CONTINUED MY EDUCATION WITH A TLR 22 4.0 BECAME BATLEY BUGGY CLUB COMMITTEE MEMBER GOT A KC TO WHILST WAITING FOR THE LAYDOWN NOW DRIVING A COUGAR LAYDOWN KC CONVERTED TO KD FOR THE WET |
#71
|
|||
|
|||
There are a few things I'm not to sure with this kit at the mo. Don't like the screws they give you for the pistons and the fact you have to modify the rear wishbones if you want to run the diff in its lowest position.
|
#72
|
||||
|
||||
Quote:
Only need to remove a very small amount of material, defo no loss in strength.
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD Last edited by mark christopher; 15-05-2019 at 09:02 PM. |
#73
|
|||
|
|||
I'm fine with the screw on piston it's the counter sunk screw with no recess in the piston for it. But it's the fact you have to remove it to use low diffs.
|
#74
|
||||
|
||||
Quote:
Aldi have a good dremel style tool on offer soon, 16 quid 3 year warranty Have you built yours yet, or are you just anti schumacher?
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD Last edited by mark christopher; 15-05-2019 at 09:18 PM. |
#75
|
|||
|
|||
Ive got a dremel sitting in my toolbox at work it's just bits like this shouldn't need doing on a top line car. Didn't have to do it on the kc and that used arms from a older car to. Didn't have to do it on the 6.1 when running the b64 arms.
Last edited by matt; 15-05-2019 at 09:26 PM. |
#76
|
|||
|
|||
Dremmeling things to get them to fit is a bit crap
|
#77
|
||||
|
||||
They fit fine...... just as said a very small amount of material needs removing in low diff position only. It's only where the drive shaft pin may rub.
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#78
|
|||
|
|||
1 degree of anti squat and low diff and they do rub, no maybe about it.
|
#79
|
|||
|
|||
Far from anti Schumacher, I've had most 2wd from the club10 up to the kc, missed out the sv line as wasn't racing at the time after having our 1st child. But I'm also not going to be a fanboy of them and blindly look over faults they have.
|
#80
|
||||
|
||||
Well I'm off to prep mine and improve my lap times, I'll leave you to find some thing else wrong
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD Last edited by mark christopher; 16-05-2019 at 06:44 AM. |
|
|