|
#1
|
||||
|
||||
Cat belt cover & alloy inner trans housing
Im after a belt cover to fit and xls/procat/bosscat, anyone know of anyone doing any repro ones ? Seen the shells but no belt covers that fit the top deck
Also after an alloy inner transmission housing if anyone has one knocking around that they fancy parting with ? Thanks
__________________
CML DISTRIBUTION -SOUTHWESTRC -HPI - RUDEBITS - MR O FOAMS - LMR - ATOMIC CARBON -STARREGORSEHOLIDAYPARK - ICON RC
|
#2
|
||||
|
||||
Those belt covers are rare as rocking horse sh*t - I haven't seen any in... forever!
|
#3
|
||||
|
||||
Also looking for one and if anyone find one send it to kamtec so it can be duplicated.
mvh Isobarik |
#4
|
||||
|
||||
dave, i`ve got a used one you can borrow as a pattern to get some made if you want. i also have an alloy inner housing that for some reason has had a hole cut in the front you can have.
Last edited by brian s; 16-02-2011 at 10:49 AM. Reason: . |
#5
|
||||
|
||||
Yes, they are very rare in good condition! I asked Team Bluegroove and they might be interested if they could get a new 'master' to work from. I'm happy with their Procat shell and undertray. Maybe someone would be willing to send them one?
|
#6
|
||||
|
||||
Cover
Quote:
__________________
Losi xx Vintage (Rc10stealth Optima mid turbo Cougar works Losi 8E Tuggy brushless 4 boys(will be expensive in rc world)
|
#7
|
||||
|
||||
lovely thanks mate
__________________
CML DISTRIBUTION -SOUTHWESTRC -HPI - RUDEBITS - MR O FOAMS - LMR - ATOMIC CARBON -STARREGORSEHOLIDAYPARK - ICON RC
|
#8
|
||||
|
||||
It's dead simple! It doesn't even need to be that spectacular as it's just to keep the transmission dirt/fluff free! I'd gladly make a mould out of wood or something if it's possible for Keith to make a mould from it!
|
#9
|
||||
|
||||
I have got moulds of 3 different types of belt covers, so I can vacform some.
One is SWB CAT, the other 2 are for long wheelbase, one has that flat rectangle thingo near the front (I think this is for a CAT XL) the other is the same length but without the rectangular bit which I think is for the Procat? Is Bosscat the same fitment aswell? |
#10
|
||||
|
||||
Put me down for one of the Procat belt covers please.
I'm sure there'll be plenty of demand... who can get these made? |
#11
|
||||
|
||||
Ta daaa found one just didnt remember that i got it....
since its not in my garage its at my parents house. mvh isobarik |
#12
|
||||
|
||||
Cool can it be sent off for some repro ones ?
__________________
CML DISTRIBUTION -SOUTHWESTRC -HPI - RUDEBITS - MR O FOAMS - LMR - ATOMIC CARBON -STARREGORSEHOLIDAYPARK - ICON RC
|
#13
|
||||
|
||||
Quote:
4 boys what if they break theire speedo at the same time...ha ha ha .... I have 3 girls and 2 of those is sharing an RC10 Teamcar with an kyosho stock 05 in it ... mvh isobarik |
#14
|
||||
|
||||
I.ll guess that it can be best would have been if it wasnt cut but i think it works and the finish is not so importante on an beltcover.
mvh Isobarik |
#15
|
||||
|
||||
Great... will you send it to TBG or Kamtec? I heard Kamtec takes forever.
The Procat shell I got from TBG is good. There's a photo in my thread Procat for Li-Fe. teambluegroove@hotmail.com |
#16
|
||||
|
||||
Quote:
Shall email him and ask. mvh Isobarik |
#17
|
||||
|
||||
Deffo interested in a repro! Willing to contribute towards costs of getting these made too - even if it means underwriting the first x off the line!*
Does anybody remember what the flat bit was for? I keep thinking it's for sticking the driver to but I think it's too far forward for that! * where x < 10 |
#18
|
||||
|
||||
How did you get on, Henrik?
btw he's got a sweet photo of my shell (paint by RCS) on his eBay listing... http://cgi.ebay.co.uk/SCHUMACHER-PRO...item2305ade745 |
#19
|
||||
|
||||
Simonl says Kamtec are making a mould for the belt cover
|
#20
|
||||
|
||||
Yeah i asked keith ?? and he had an mold but he was not sure that it was fitting right so he said that he would send me one to try but i havent recived it yet.
mvh isobarik |
|
|