Bone popping out of outdrive on X-6

[josh_smaxx]

Ok, the situation as stands:

3mm of limiters in shockers
3 shims on each CVD axle
-2* camber
inside hole on wishbones, 3rd in on tower

The bones is hanging out of the outdrive, i want to run -1* camber but it just pops out.

What do i do?

[Darren Boyle]

Have you got the BK2 CVD axles fitted, these will cure it if not.....

[josh_smaxx]

No i havent, its just standard kit + FT B4

BTW, thanks for geting it to me so quick i might be ringing you later on about some spares.

[Chequered Flag Racing]

Originally Posted by josh_smaxx

Ok, the situation as stands:

3mm of limiters in shockers
3 shims on each CVD axle
-2* camber
inside hole on wishbones, 3rd in on tower

The bones is hanging out of the outdrive, i want to run -1* camber but it just pops out.

What do i do?

shim it out some more to stop it happening with the kit cvd's

think I may have 8mm or more in mine

[Chequered Flag Racing]

Originally Posted by DMS Racing

Have you got the BK2 CVD axles fitted, these will cure it if not.....

Darren

list the parts for the BK2 conversion please

[josh_smaxx]

Originally Posted by Chequered Flag Racing

shim it out some more to stop it happening with the kit cvd's

think I may have 8mm or more in mine

I would but i dont have any shims left oh and i found a full set of your anti-squat shimz in the box of tricks i bought off James Shanley.

[bigred5765]

u need the bk2 axles really, but i re drill of the drive shaft will help in the mean time, never don't it myself but I'm sure someone will tell you how fare out you need to come,2-3mm is my guess.

[Chequered Flag Racing]

Originally Posted by josh_smaxx

i found a full set of your anti-squat shimz in the box of tricks i bought off James Shanley.

there no use inside the shocks

[josh_smaxx]

If i put one in the shocks it might stop the bones popping out though

dont worry i wont. I need more shims wonder if DMS have any......

[Chequered Flag Racing]

Originally Posted by bigred5765

u need the bk2 axles really, but i re drill of the drive shaft will help in the mean time, never don't it myself but I'm sure someone will tell you how fare out you need to come,2-3mm is my guess.

re-drill the B4 kit axles for the drive pin so that you shim the axle inwards in the upright?

[josh_smaxx]

I think its something like that, but i dont have a pedstle drill so ill get the BK2 axles.

Is this the part number for the shims AS31162?

[Lee]

just use any spacer josh, thats all i did.

If you ask rich lowe how many i had in my shocks at the clash he will tell you it was about 14 mm.

Eventually i realised i was using xx4 rear shocks

[josh_smaxx]

If gone through every box i have, i dont have anymore spacers. I have the big ones that go between the bearings in the hubs but thats to much, iv checked.

[Lee]

hmmm, im sure we can sort something for you, just use all the pistons you are not currently using

[Mike Hudson]

how can you not have any shocks spacers? go raid your house you got any of the red rubber shocks seals?

[Rick]

If you are desperate then strip a bit of insulation from some motor wire and cut to length

[josh_smaxx]

woah woah woah, crossed lines here badly. Im talking about shims on the axle iv got loads of stuff that'll go in the shocks.

[Mike Hudson]

maybe 1mm more in the shocks will do the trick then

[rcracer]

just buy the bk2 axels it will save you all this hassle

[josh_smaxx]

Originally Posted by rcracer

just buy the bk2 axels it will save you all this hassle

I was thinking along those lines