|
|||||||||||||||
|
#1
|
||||
|
||||
|
in the cat, what the best mod to have more drop at the rear?
__________________
My Hamster "Leela" drive more better of me!!! |
|
#2
|
||||
|
||||
|
I use the turnbuckle rod ends instead of the std short ones on the bottom of the shock. And a 3/4qtr one on the front.
P
__________________
Schumacher CAT K1 Schumacher Cougar SVII Schumacher Racing - Team Tekin - Spektrum - Inside Line Racing - TrishBits |
|
#3
|
||||
|
||||
|
I'm looking at doing this too.
How many people are running with the different cups? |
|
#4
|
||||
|
||||
|
we have always run them its worth doing,and try to run as small amount of washers at the rear to lift the wishbone high,
__________________
Mattys the driver,my names carl
|
|
#5
|
||||
|
||||
|
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.
Mike
__________________
Retired Racer |
|
#6
|
||||
|
||||
|
.75 of an inch then on the rear shocks?
|
|
#7
|
||||
|
||||
|
Quote:
how much weight is grant running |
|
#8
|
||||
|
||||
|
we run about the same weight.108grms if i remember right,
__________________
Mattys the driver,my names carl
|
|
#9
|
||||
|
||||
|
Im rather new to the schey, where is the weight located ? front bia's, rear bia's ... 50/50 ?? also is this weight to make the car legal at the events or required for better handling ?
|
|
#10
|
||||
|
||||
|
What's the part number for the 3/4 lengh ball links ?
I'm interesed as to what weight the the team run too? |
|
#11
|
||||
|
||||
|
there isnt a 3/4 lenth ball joint. get the longer ones for the turnbuckles and cut them to the desired lenth
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
|
#12
|
|||
|
|||
|
Nath is right, just cut them down to the correct size. As for weight, for me it varies depending what track im at. I know Grant is pretty steady around the 108g mark, but at Worksop and the Euros i didnt run any. I prefer a more lively car than Grant, so comes down to what you like really.
Positioning the weight, when I don run some its under the chassis as central as possible. The weight distribution on the car is fine so no need to run it to the front or back. Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC |
|
#13
|
||||
|
||||
|
Quote:
Think it's .75 for the full length ones. Surprised they haven't released new cups as option parts etc. |
|
#14
|
||||
|
||||
|
for positioning on Matty's car i never move it, but as Si said we did remove ours for the euros,but back in the UK we haven't removed it yet but we also haven't run ares indoors yet, ill attach a pic of ours,it'll have to be a bit later flat battery
__________________
Mattys the driver,my names carl
Last edited by bigred5765; 24-09-2009 at 10:25 AM. Reason: because G has become a english teacher:) |
|
#15
|
||||
|
||||
|
"ours"
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Love you Lion-o
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
|
#16
|
||||
|
||||
|
__________________
Mattys the driver,my names carl
|
|
#17
|
||||
|
||||
|
Measured the ballcups and the turnbuckle ones are about 19mm and the standard ones are about 14mm.
3/4 of the turnbuckle ends is 14.25mm |
|
#18
|
||||
|
||||
|
not quite..... as you have long and short there make the 3/4 ones half way inbetween ie aprox 16.5-17mm
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
|
#19
|
||||
|
||||
|
just measured mattys ball joints for ya mikey,
long =19mm 3/4 = 16.5mm short = 14mm
__________________
Mattys the driver,my names carl
|
|
#20
|
||||
|
||||
|
Quote:
|
![]() |
|
|