|
|||||||||||||||
|
#1
|
||||
|
||||
|
is anyone running one with a brushless motor if so can you answer the following.
1. which mods have been done to the slipper/belts/motor plate if any. 2. what brushless motor limit/turn are you running in the car with mods or without mods. 3. has it been running without problems on either of the above. thanks guys.
__________________
2002, 3 , 4 B.R.C.A Scottish indoor TC champion. 2005......... B.R.C.A Open modified Scottish TC champion. 2011....... Scottish Indoor OFF-ROAD champion. 2012 ......... Scottish SORC Off-Road Runner up. 2022.....x2 scottish sorc sors vetern champion My oOple Trader feedback http://www.oople.com/forums/showthread.php?t=84630 |
|
#2
|
||||
|
||||
|
Quote:
Anyone?, i saw one running at the oople race, im sure it was stu,s.
__________________
2002, 3 , 4 B.R.C.A Scottish indoor TC champion. 2005......... B.R.C.A Open modified Scottish TC champion. 2011....... Scottish Indoor OFF-ROAD champion. 2012 ......... Scottish SORC Off-Road Runner up. 2022.....x2 scottish sorc sors vetern champion My oOple Trader feedback http://www.oople.com/forums/showthread.php?t=84630 |
|
#3
|
||||
|
||||
|
It was my bosscat at the oople event, i was using a 9 single brushed motor with a lrp esc & orion lipo
Right if your going brushless then you will deffo need the slipper clutch fitted, mine also had 4 disc spring washers fitted to each diff, these are essential to stop the diffs undoing, they are not shown in the manual but are shown in the procat manual, if you can find some then alloy diff washer carriers would be a very good idea, i melted the plastic ones with the brushed motor If you stick the extras on then brushless shouldn't be a problem but i wouldn't go mad, maybe a 8.5-10.5t Hope that helps Martin
__________________
A rc car is not just for christmas, it's for life
|
|
#4
|
||||
|
||||
|
Good advice! Stu's identified the most important and practical upgrades. Also check that the belts/diffs are tensioned correctly and that the old bearings are nice and free.
There's loads more ideas in my main thread ![]() My Procat did well with 6.5T but I'm going down to 10.5T in the hope it will be easier to drive (for me) and preserve my spares for longer ![]() http://www.youtube.com/watch?v=PZIkSMEYosQ
__________________
http://www.planetsteelexpress.com/R50token/ |
|
#5
|
||||
|
||||
|
I would also note that is can be surface dependant. I was running an 8.5T in my procat on carpet and was getting belt skip. I had to run the slipper very free and not be brutal with the throttle. I'm investigating having some new rear drum diffs made at the moment, when I get some proper details I will post something up.
|
|
#6
|
||||
|
||||
|
Quote:
thanks stu, i had fitted the brushless motor in place atm but it seems i might have to extend the motor slots longer to achieve more purchase for variation sizes for pinions? not sure if you had such a problem as you were running a brushed mod. 4 disc spring washers & alloy diff washer carriers.can these still be gotten? kaszal :- yes mate everything is free and running well as the car was rebuilt. i was hoping to give it a go on grass maybe with an 8.5t. as for holding in lipo saddles what would be best. maybe ae pillars and carbon straps with the thumb screws?. also my main concern is the wheel hexes on the rims, im sure back in the day when i did run my bosscat i stripped a few of these, i cant imagine what they would be like now, but i guess it will be getting the diffs and slipper adjusted bang on for this. thanks guys
__________________
2002, 3 , 4 B.R.C.A Scottish indoor TC champion. 2005......... B.R.C.A Open modified Scottish TC champion. 2011....... Scottish Indoor OFF-ROAD champion. 2012 ......... Scottish SORC Off-Road Runner up. 2022.....x2 scottish sorc sors vetern champion My oOple Trader feedback http://www.oople.com/forums/showthread.php?t=84630 |
|
#7
|
||||
|
||||
|
The original 1/8" disc springs are hard to find but you can use U857 instead. They are bigger so you won't be able to fit the dust caps unless you use Big 6 outdrives. However bear in mind they will also affect the driveshaft length...
http://www.oople.com/forums/showpost...1&postcount=87 The castle adaptors on the hubs are fine if they're undamaged and lined up correctly. I inserted crush spacers so the wheel bolts could be done up more securely without the bearings binding... http://www.oople.com/forums/showpost...&postcount=164 Yes, the motor position is limited. Different spurs will help. I designed my own straps and trays... http://www.oople.com/forums/showpost...&postcount=648
__________________
http://www.planetsteelexpress.com/R50token/ |
|
#8
|
||||
|
||||
|
Quote:
thanks for your advice and help, its greatly appreciated kaszal.
__________________
2002, 3 , 4 B.R.C.A Scottish indoor TC champion. 2005......... B.R.C.A Open modified Scottish TC champion. 2011....... Scottish Indoor OFF-ROAD champion. 2012 ......... Scottish SORC Off-Road Runner up. 2022.....x2 scottish sorc sors vetern champion My oOple Trader feedback http://www.oople.com/forums/showthread.php?t=84630 |
![]() |
|
|