|
#41
|
|||
|
|||
Yeah I'll be drawing them up so I can just rattle em off when needed
|
#42
|
|||
|
|||
Ok mate lovely job I'll pm you when they're ready
|
#43
|
||||
|
||||
cheers mucka
__________________
YZ2 sanwa hi-tec Balls out zx6 Futaba orion sanwa Need a liner resized ? Liars run for cover the truth is taking over!!! |
#44
|
||||
|
||||
Not sure, any rubbing against the side of the shock body could cause them to pick up or leave tiny fleck's floating about in the oil
__________________
----Cougar 2 team----Cougar 2 works----Cougar 2000---- ----Schumacher Bosscat---- ----Traxxas TRX1----Losi XXX CR----Losi XXX BK2---- ----AE B4 ft----Xfactory X6^----DEX210 V1---- ----TLR22 3.0----TLR22 4.0----TLR22t 4.0----TLR22 5.0AC---- ----AE B6.4----
|
#45
|
|||
|
|||
Some 1/8th scale big bores (tapered) fresh off the machine
|
#46
|
|||
|
|||
how you getting on with the Durango big bores?
|
#47
|
|||
|
|||
I was fortunate enough to be sent some Kyosho BB pistons to try,
I must say they look fantastic, the machining is as good as Kit, If not better. They fit like a glove! Also they are very easy to work with & drill. I have built them up and they feel really smooth on the bench, Il be testing them over the week. I will give some more feedback when I've raced the car, although I foresee no issues!! Thanks!! |
#48
|
||||
|
||||
Ok after some fighting with my PC I finally managed to get this picture up.
Do you believe this is possible to not only make the piston but also cut out the holes? The below are traxxas TRX1 shock pistons alongside one associated piston. I would like to have the exact hole sizes from the traxxas pistons cut out on a blank Associated (not big bore) shock piston Im after one hole set of four, a two hole set of four and three hole set of four. Please let me know if this is possible. Thanks.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#49
|
|||
|
|||
Yes mate they are possible to make but I will have to either have one to copy or a good accurate drawing of what you want also may take a while for me to get onto a machine with a C axis to mill the slots
|
#50
|
||||
|
||||
Hello mate,
What the price be on some tapered pistons to fit the losi 1/8scale shocks?? Cheers Jay |
#51
|
||||
|
||||
1/8 scale pistons
Hello mate,
What would the price be on some tapered pistons to fit the losi 1/8scale shocks?? Cheers Jay |
#52
|
|||
|
|||
Pistons are £1 pound each mate for whatever car, just need one to copy as I've not done any for that car as yet
Cheers john |
#53
|
||||
|
||||
top!
__________________
|
#54
|
|||
|
|||
Gixxer,
PM sent |
#55
|
||||
|
||||
Is there any chance you could pm me the address to send my pistons to. Thanks.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#56
|
|||
|
|||
This week ill be running schuy small bores and kyosho bb let me know asap If you want either to save on setup time
|
#57
|
||||
|
||||
pistons look good john won't have chance to try them till end of the month though just sent cash
__________________
YZ2 sanwa hi-tec Balls out zx6 Futaba orion sanwa Need a liner resized ? Liars run for cover the truth is taking over!!! |
#58
|
|||
|
|||
Thanks mate
|
#59
|
||||
|
||||
How do, did you get my package, and can you do. If yes please send me via PM your paypal address so I can pay you for this, Cheers.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#60
|
|||
|
|||
Hello people to those who have sent me pistons to copy recently I have been sick and still busy with work and haven't got thru as much as I'd like to, bit will be hittin it hard this week to get them all done and sent back to you. Yeah welshy I got it will get them done asap for ya
Cheers john |
|
|